Advanced Robotics Programming: Difference between revisions
Jump to navigation
Jump to search
| Line 18: | Line 18: | ||
Even though the game of each season changes, a lot of subsystems repeat themselves season after season. Therefore, our Framework Library provides generalized subsystems to handle any generic use. Here are some typical subsystems you will find on a robot. | Even though the game of each season changes, a lot of subsystems repeat themselves season after season. Therefore, our Framework Library provides generalized subsystems to handle any generic use. Here are some typical subsystems you will find on a robot. | ||
* Motor Actuators: the | * '''[[Motor Actuators]]''': Motor is the most fundamental output device on a robot. It provides movements for mechanisms. Motor Actuators contain one or more motors, an encoder to keep track of its position and some limit switches to limit their movement. FIRST provides some basic motor classes (e.g. DcMotor, DcMotorEx in FTC and Phoenix5/Phoenix6/SparkMax in FRC). The Framework Library added a lot more features on top of that in different layers of complexity in the TrcMotor class. For example, it added support for a digital input sensor to reset the motor encoder automatically (limit switches). This is useful for using the motor in a complex actuator such as an arm or elevator when you may need to zero calibrate the zero position of the actuator using a lower limit switch. It also added support to provide velocity mode control and motor odometry. On top of the fundamental motor features, it also provided PID Controlled functionality. It can support either native motor close-loop control (position and velocity PID control) or software PID control in case some motors do not support native close-loop control (e.g. continuous servos). TrcMotor added support for lower and upper limit switches, motor stall protection for safety, multiple motors with synchronization (motor followers), zero position calibration and gravity compensation. These advanced features made it trivial to implement complex subsystems such as swing arm, elevator, slide or turret. The built-in PIDF controller allows the arm or elevator to be controlled by an analog joystick to speed up or slow down the arm/elevator movement. It understands the arm/elevator position approaching the lower/upper position limits and will automatically slow down its movement. It also provides stall protection. If the PID Actuator got stuck and the motor is stalled, it can cut motor power to prevent it from burning out. It also allows a reset timeout so that the stall condition can be cleared after a certain period assuming the stall condition is caused by human temporarily. This allows the subsystem to resume its function and provides time for the motor to cool down. In addition, it also supports voltage compensation. It understands battery voltage drop and can compensate the power level sent to the motor. | ||
* Intake | * Intake | ||
* Conveyor | * Conveyor | ||
Revision as of 02:05, 27 June 2024
The Advanced Robotics Programming Class focuses on teaching our Titan Robotics Framework (TRC Library). The target audience of this Programming Class is for students who already have basic knowledge of the Java language. The class is primarily designed for FRC although it is also applicable for FTC because our TRC Library is shared between FTC and FRC. After finishing this class, you should be able to write code for both FTC and FRC robots with some platform specific differences.
Programming Software Installation
Before coming to the programming class, you need to install the required software on your laptop. Please do this at home before coming to class. We do not want to dedicate class time to install software because they are time consuming and require downloading gigabytes of data from the Internet which would overwhelm our Internet bandwidth if all students were downloading at the same time. Therefore, please make sure you finish these tasks at home before coming to class.
TeleOp Driving Your Robot Right Out-Of-The-Box
At this point, you should have installed all necessary software for developing robot code and also clone the robot template code from the GitHub repo. Since the template already contains basic code for three different kinds of robot base (Differential Drive, Mecanum Drive and Swerve Drive), it takes very few modifications to make it work with any of the three types of robots.
Creating Subsystems
Once the drive base is fully operational, the next step is to create subsystems for the robot such as Elevator, Arm, Intake, Grabber etc. It is a good practice to create subsystems as separate Java classes that encapsulate all hardware related to those subsystems. To create a subsystem, you need to determine the following:
- What hardware does the subsystem contain? This includes motors, actuators and sensors. For example, an elevator will most likely contain a motor to move it up and down, an encoder to keep track of its position and one or two limit switches to tell if the elevator has reached its lower or upper height limit.
- What operations does the subsystem support? For example, an elevator may have a method to allow the joystick to control it going up and down at various speed, a method to command the elevator to go to a certain height, and a method to command the elevator to go to next preset height up or down.
Even though the game of each season changes, a lot of subsystems repeat themselves season after season. Therefore, our Framework Library provides generalized subsystems to handle any generic use. Here are some typical subsystems you will find on a robot.
- Motor Actuators: Motor is the most fundamental output device on a robot. It provides movements for mechanisms. Motor Actuators contain one or more motors, an encoder to keep track of its position and some limit switches to limit their movement. FIRST provides some basic motor classes (e.g. DcMotor, DcMotorEx in FTC and Phoenix5/Phoenix6/SparkMax in FRC). The Framework Library added a lot more features on top of that in different layers of complexity in the TrcMotor class. For example, it added support for a digital input sensor to reset the motor encoder automatically (limit switches). This is useful for using the motor in a complex actuator such as an arm or elevator when you may need to zero calibrate the zero position of the actuator using a lower limit switch. It also added support to provide velocity mode control and motor odometry. On top of the fundamental motor features, it also provided PID Controlled functionality. It can support either native motor close-loop control (position and velocity PID control) or software PID control in case some motors do not support native close-loop control (e.g. continuous servos). TrcMotor added support for lower and upper limit switches, motor stall protection for safety, multiple motors with synchronization (motor followers), zero position calibration and gravity compensation. These advanced features made it trivial to implement complex subsystems such as swing arm, elevator, slide or turret. The built-in PIDF controller allows the arm or elevator to be controlled by an analog joystick to speed up or slow down the arm/elevator movement. It understands the arm/elevator position approaching the lower/upper position limits and will automatically slow down its movement. It also provides stall protection. If the PID Actuator got stuck and the motor is stalled, it can cut motor power to prevent it from burning out. It also allows a reset timeout so that the stall condition can be cleared after a certain period assuming the stall condition is caused by human temporarily. This allows the subsystem to resume its function and provides time for the motor to cool down. In addition, it also supports voltage compensation. It understands battery voltage drop and can compensate the power level sent to the motor.
- Intake
- Conveyor
- Shooter
- Grabber
Connecting Subsystems to the Robot
- Instantiate the subsystems
- TeleOp control of the subsystems
- Display subsystem status